Danfoss EVR Solenoid Valves & Coils — Selection Guide

Guide compiled by cBallast. 8-page PDF; the full content is on this page.
Brand
Danfoss
Subject
Refrigerant solenoid valves
Document type
Guide
Reference
2026 edition
Issued
2026-11-10
Pages
8
Format
Web page and PDF

The refrigeration solenoid workhorse decoded: EVR sizes 2 to 40 and what the number means, direct against servo operation and the minimum pressure differential that explains most "valve will not open" calls, NC against NO versions, EVRH for high-pressure duty, the clip-on coil system (coil families, voltage codes, AC against DC, cable plugs) that lets a dead coil be changed without opening the line, seal and service kits by size group, the cross-reference logic to Castel and Emerson-Alco solenoids, and the RFQ lines that identify a valve exactly from what is stamped on it.

The short version

1. Reading an EVR — what the markings mean

Marking elementExampleMeaning
Family + sizeEVR 6Capacity/connection class — e.g. the EVR 6 3/8" solder valve (032F1212)
Code number032F1212The exact orderable variant: size + connection type/size + NC/NO + options. The 032F prefix is the solenoid-valve program; quote this number and the identification is finished
Connection3/8" ODF solder, or SAE flareSolder (LD suffix habits in wholesale listings) dominates fixed installs; flare survives in service work
NC / NONC default; NO markedNC opens when energised (liquid-line standard); NO closes when energised (hot gas, defrost schemes)
EVRHEVRH 6High-pressure variant for modern refrigerant duties — kits differ (032F8165), do not mix with standard EVR kits
Manual stemSpindle under a capLets the plant run with a dead coil — and tells you at service why a "closed" valve is passing: the stem was left open

If the plate is unreadable: measure the connection (type and size), note NC/NO from the schematic, read the coil's own label for voltage, and send photos of body and stamping — that identifies the 032F code in one pass. The Danfoss code decoder guide covers the neighbouring number families (060, 018F, 032F, 084).

2. Direct or servo — and the minimum pressure differential

ConstructionSizes (typical)Opens atConsequence
Direct-operatedThe small end of the family (EVR 2/3 class)Zero pressure differential — the coil lifts the plunger directlyWorks on equalised lines, bypasses, small capacities
Servo-operated (pilot + diaphragm/piston)EVR 6 and upNeeds a minimum differential (of the order of a few hundredths of a bar) to use line pressure as the muscleOn an equalised or dead line it opens a pilot path only — the classic "energised but not flowing" call

Three field consequences worth a technician's tattoo: a servo EVR cannot be used as a vacuum-breaking or zero-Δp bypass valve — select a direct-operated size or a different family; an oversized solenoid on a lightly loaded liquid line may never see its minimum differential and will chatter or hunt — size by capacity, not by pipe; and MOPD (maximum opening pressure differential) is a coil-power property — a 10 W coil opens against less differential than a 20 W DC coil, so coil substitutions change the valve's capability, not just its voltage.

3. The coil system — voltages, families, plugs

Coil family (letters)CharacterTypical codesCatalogue anchors
BB class — AC clip-on, 10 WThe standard AC coil for EVR bodiesBB230AS (230 V), BB024AS-class (24 V 50 Hz)BB230AS DIN-spade; 018F7358 24 V 10 W
BN class — DC, 20 WDC supply duty (marine, mobile, control systems)BN024DS (24 V DC)BN024DS; see also the BN024AS 24 V AC 24 W step-up
BE class and siblingsVariants by terminal style and powerBE230AS classQuoted by code
Code logicLetters = family/power class; digits = voltage; A/D = AC/DC; final S-class letters = terminal type (DIN spade, cable, terminal box). The 018F prefix on the code number is the coil programme itself
Cable plugsDIN-spade plugs with or without indicator lampBy coil voltage230 V plug, 24 V plug — fits 018F/018Z/042N type-B coils

Replacement rules that prevent returns: match voltage AND frequency AND AC/DC exactly (a 230 V AC coil on 24 V does nothing; a 24 V AC coil on 24 V DC burns); never energise a clip-on coil off the valve (it overheats within minutes without the core); and when a coil has burned once, check why — overvoltage, moisture in the plug, or a stuck armature — before fitting its twin. A spare coil per voltage class belongs in every plant's drawer: it is the single highest-frequency refrigeration RFQ line we see, precisely because the body stays in the line.

4. Where EVRs sit in the system — and selection by duty

DutySelection logicPartner components
Liquid line (pump-down control, tight shut-off at stop)NC, sized to liquid capacity at the design Δp — the standard caseFilter drier upstream, sight glass downstream, TEV per the expansion valve finder
Suction lineLarger body for the vapour volume at low Δp — size from capacity tables, never by pipe diameterCheck valve logic per system design
Hot gas (defrost, bypass)NO versions and high-temperature coils by scheme; EVRH territory at higher pressuresDefrost control per the EKC / AK-CC controller guide
Zero-Δp or equalised linesDirect-operated small sizes only—

Installation discipline the datasheet assumes: flow arrow respected, coil removable upward with service clearance, body protected from solder heat (wrap it wet or disassemble per instructions — overheated PTFE seats are the hidden cause of "new valve leaks"), and a strainer or drier upstream because servo pilots and scale do not coexist. Industrial-refrigeration positions (ammonia, large CO2) belong to the ICF/SVA programme instead — see the SVA/ICF guide; water and neutral-fluid duty belongs to the EV2xx family in the solenoid valve finder.

5. Cross-reference and the RFQ line

Cross-brand method (full tables in the cross-reference guide): match (1) duty and NC/NO function, (2) capacity at the actual refrigerant and Δp — not nominal size names across brands, (3) connection type and size, (4) refrigerant/pressure approval (standard vs high-pressure variants), (5) coil voltage and power separately, because every maker sells coil and body apart. Castel's 10x8-series and Emerson/Alco's 200RB class map onto EVR duties cleanly at the class level; the exact pairing is by capacity table, which we run per line. A complete RFQ line reads: code number if known (032F…), else family+size, connection, NC/NO, refrigerant, and the coil as its own line (voltage/frequency/AC-DC, plug wanted or not). ASCO-pattern general solenoids on air/water live in their own world — the 8210 cross-reference — do not cross refrigerant valves against them.

How buying works at cballast. We stock and quote EVR bodies, the full coil programme, plugs and service kits, cross Castel and Alco positions by capacity table with the basis stated per line, and flag the servo/minimum-Δp trap when an inquiry smells like a zero-differential application. Accounts are vetted at onboarding; first order prepaid; established accounts on credit terms with repeat discounts; public bodies and utilities invoiced against purchase order from the first order. RFQs to sales@cballast.com.

Frequently asked questions

Why does my Danfoss EVR valve hum but not open?
If it is EVR 6 or larger it is servo-operated and needs a minimum pressure differential across the valve to open fully. On an equalised or dead line the coil is fine and the valve is behaving per design. Check system pressures first, the manual stem position second, and only then suspect the coil or the pilot orifice (dirt).
Can I replace just the coil on an EVR solenoid valve?
Yes — that is the design's point. Clip the old coil off and the new one on without opening the refrigerant circuit, matching voltage, frequency and AC/DC exactly. If a coil failed, find out why (overvoltage, moisture, stuck armature) before the replacement repeats the funeral.
What is the difference between EVR NC and NO?
NC (normally closed) opens when energised — the standard for liquid-line and pump-down duty. NO (normally open) closes when energised — used in hot-gas, defrost and fail-open schemes. They are different valves, not a wiring choice; the code number differs.
What does the number in EVR 6, EVR 10, EVR 20 mean?
It tracks the capacity/connection class of the body — bigger number, bigger orifice and connections. Selection is by capacity at your refrigerant and pressure drop from the Danfoss tables, not by matching the number to pipe size; an oversized servo valve that never sees its minimum differential is a worse problem than a correctly sized smaller one.
What is EVRH?
The high-pressure variant of the family for modern high-pressure refrigerant duties. Bodies and kits are specific — the EVRH 6/8 seal kit (032F8165) is not the standard EVR kit — so quote the H when the plate shows it.
Is there a Castel or Alco equivalent to a Danfoss EVR?
At class level, yes — Castel 10x8-series and Emerson/Alco 200RB-class solenoids serve the same duties. A legitimate cross matches capacity at the refrigerant, connection, NC/NO and pressure rating, with the coil specified separately. We state the basis on every crossed line; the method lives in our refrigeration cross-reference guide.
Which coil do I need for an EVR valve?
Read the supply first: 230 V AC and 24 V AC take the standard 10 W class clip-on coils (BB230AS and siblings); 24 V DC takes the 20 W DC class (BN024DS). Add the matching DIN-spade cable plug — with indicator lamp where fault-finding matters. Send the valve code and supply voltage and the coil line writes itself.
Who supplies Danfoss EVR valves and coils?
cballast.com stocks EVR bodies, coils, plugs and service kits and quotes Castel/Alco crosses with the basis stated. Write to sales@cballast.com with the 032F code or a photo of the stamping.

References and related guides

Standards and sources referenced: Danfoss EVR/EVRH datasheets and capacity tables, Danfoss coil programme documentation (018F series), EN 60730-class coil practice; peer data from Castel and Emerson/Alco catalogues for the cross-reference method.

Questions on a valve you cannot identify or a zero-differential application: write to sales@cballast.com. We answer whether or not you buy from us.

Open / Download PDF

Compiled by cBallast for identification and cross-reference. Part numbers, designations and trademarks belong to their respective manufacturers. Confirm ratings and dimensions against the manufacturer's current documentation and the nameplate of the installed equipment before ordering or installation.