Intrinsically Safe Barriers — Zener vs Galvanic Isolators

Selection guide compiled by cBallast. 9-page PDF; the full content is on this page.
Compiled by
cBallast
Subject
Intrinsic safety barriers and isolators
Document type
Selection guide
Reference
2026 edition
Issued
2026-11-09
Pages
9
Format
Web page and PDF

How intrinsic safety works under IEC 60079-11, the real difference between a Zener barrier and a galvanic isolator, the entity parameter arithmetic (Uo, Io, Po against Ui, Ii, Pi plus cable Co and Lo), the earthing rules that decide between them, loop examples for 4–20 mA transmitters and RTDs, and the MTL and Pepperl+Fuchs module families — with catalogue examples and replacement logic.

The short version

1. How intrinsic safety works

Ex i limits the electrical energy available in the hazardous area so that neither a spark (opening/closing/shorting the circuit) nor a hot surface can ignite the surrounding atmosphere, with safety factors applied and faults assumed: Ex ia tolerates two countable faults (Zone 0-capable as part of a system per 60079-25 practice), Ex ib one fault (Zone 1), Ex ic the normal-operation level (Zone 2). The limits depend on the gas group — IIC (hydrogen, acetylene) is the strictest, IIB (ethylene) and IIA (propane) progressively easier — which is why the same barrier delivers less usable power when certified for IIC. The practical ceiling for a IIC loop is around 25–28 V, 93–300 mA resistor-limited, of the order of 1.2–1.3 W; enough for transmitters, RTDs, solenoid pilot valves of IS type, switches and LED beacons — never for motors or heaters.

2. Zener barrier vs galvanic isolator

PropertyZener barrierGalvanic isolator
PrincipleZener clamp + series resistor + fuse; passiveSame limiting + transformer/opto isolation; active
IS earthRequired: dedicated, low impedance (≤ 1 Ω to the main earth), proven and maintainedNot required; loop floats
Power supplyNone24 V DC safe-area supply
SignalPass-through; adds end-to-end resistance (voltage headroom must be checked)Repeats/conditions; HART pass-through on standard models; can convert (RTD in, 4–20 mA out)
Earth faults on the loopCan blow the fuse / kill the loopTolerated; isolation breaks ground loops
Cost per channelLow2–4x Zener
Typical 2026 useReplacements in existing Zener installations; simple switch and LED circuits; metering loops where the passive path is preferredNew installations, marine and offshore, anywhere the IS earth is not worth owning

Catalogue anchors for both camps: the MTL7089 shunt-diode Zener barrier, 28 V / 300 Ω is the classic transmitter-loop Zener; the MTL5541 isolated transmitter power supply is its galvanic successor for 4–20 mA loops (HART-transparent repeater power supply), and the MTL5575 temperature converter takes an IS RTD or thermocouple in and gives 4–20 mA out. Pepperl+Fuchs' K-system and Eaton's MTL4500/MTL5500 ranges mirror each other function for function; combined units exist too (the EXB-2000 Zener barrier/galvanic insulator for flow loops in our catalogue is one maker-specific example), and replacement modules for packaged systems appear as items like the OWS IS analogue repeater (replacement).

3. Entity parameters: the five comparisons

Every certified IS device publishes entity parameters. The barrier/isolator (associated apparatus) states what it can deliver: Uo (max output voltage), Io (max output current), Po (max output power), and the external reactances it may see: Co (max cable+device capacitance) and Lo (max inductance), sometimes as an Lo/Ro ratio. The field device states what it can accept: Ui, Ii, Pi, and what it adds: Ci, Li. The loop passes when:

#CheckRule
1VoltageUi (device) ≥ Uo (barrier)
2CurrentIi ≥ Io
3PowerPi ≥ Po
4CapacitanceCi + C(cable) ≤ Co
5InductanceLi + L(cable) ≤ Lo (or Lo/Ro respected)

Cable values come from the cable datasheet (typical instrument pair: 80–200 pF/m and about 0.7–1 μH/m — 500 m of pair at 120 pF/m is 60 nF against a typical Co of 80–160 nF for a 28 V IIC barrier). The system file (per IEC 60079-25) records the five comparisons per loop, with the certificates. This paperwork is what a surveyor or auditor actually reads, and assembling it is a supplier task we quote together with the hardware: certificates for every item, parameters tabulated per loop.

4. The earthing question, settled

A Zener barrier works by diverting fault energy to earth; its safety case collapses if that earth is poor. Hence the dedicated IS earth conductor from the barrier busbar to the plant's main earthing point, kept separate from power earths, with a proven total resistance commonly held below 1 Ω and inspected on a schedule. That infrastructure — not the barrier price — is the real cost of the Zener approach, and the reason floating galvanic isolators took over new work on ships, offshore units and most plants. If you inherit a Zener installation with a healthy IS earth, keeping it and replacing modules like-for-like is entirely sound engineering; if the earth's integrity is unknown, budget the survey before trusting it.

5. Standard loop recipes

LoopZener routeIsolator route
4–20 mA transmitter (pressure, level)28 V / 300 Ω barrier (MTL7089 class); check voltage headroom: supply − barrier drop ≥ transmitter minimum at 20 mARepeater power supply (MTL5541 class / P+F KCD2-STC); HART passes
RTD / thermocoupleDual-channel Zener; lead resistance mattersTemperature converter (MTL5575 class), 4–20 mA out, linearised
Switch / NAMUR proximity sensorSimple Zener + safe-area relaySwitch amplifier with line-fault detection (NAMUR EN 60947-5-6) — detects open and short circuit
IS solenoid / beaconRarely done with Zener (power)Solenoid driver module, matched to the valve's entity parameters

The transmitter side of these loops is specified in our instrument specification guide; NAMUR sensor choices in the proximity sensor cross-reference.

6. Specifying and replacing

A complete barrier/isolator line on a requisition: function (repeater power supply, switch amplifier, temperature converter, solenoid driver), channels, Ex marking required ([Ex ia Ga] IIC for Zone 0 loops), entity parameters needed by the already-chosen field device, HART yes/no, line-fault detection yes/no, mounting (DIN rail, backplane), supply voltage, and — for replacements — the installed part number. Replacement logic: within MTL, 7000-series Zeners map to 7000-series successors, MTL4500 (backplane) and MTL5500 (DIN rail) carry the function in the last two digits (a 5541 is the DIN-rail twin of a 4541); across makers, match function and entity parameters, never just the channel count. Our team crosses MTL, Pepperl+Fuchs, Stahl and GM International module for module, with certificates attached — the marking logic itself is decoded in the ATEX/IECEx zoning and marking guide.

How buying works at cballast. We quote IS barriers and isolators by function and entity parameters with the certificates and per-loop parameter tables included, successors for obsolete modules declared next to like-for-like options. Accounts are vetted at onboarding; first order prepaid; established accounts on credit terms with repeat discounts; public bodies and utilities invoiced against purchase order from the first order. RFQs to sales@cballast.com.

Frequently asked questions

What is the difference between a Zener barrier and a galvanic isolator?
Both limit the energy reaching a hazardous-area circuit per IEC 60079-11. A Zener barrier does it passively (diodes, resistor, fuse) and must sit on a dedicated low-impedance IS earth; a galvanic isolator does it behind transformer or opto isolation, needs a 24 V supply but no IS earth, and can repeat or convert the signal. New installations mostly use isolators; Zener installations are maintained like-for-like.
What are entity parameters?
The certified electrical limits that make an IS loop checkable: the barrier's output values Uo, Io, Po and allowed external Co, Lo against the field device's input ratings Ui, Ii, Pi and its internal Ci, Li plus the cable's capacitance and inductance. Five comparisons — voltage, current, power, capacitance, inductance — all of which must pass.
Does a galvanic isolator need an intrinsically safe earth?
No. The isolation barrier means no fault current needs a drain to earth, which is its main advantage: the loop floats, ground loops are broken, and the 1 Ω IS-earth infrastructure of Zener systems is not needed.
Can HART pass through a safety barrier?
Through a Zener barrier, yes inherently (it is a passive series element). Through galvanic isolators, only models specified as HART-transparent — the standard repeater power supplies (MTL5541 class, P+F KCD2-STC class) are; always confirm it on the datasheet if configuration from the control room matters.
What does [Ex ia Ga] IIC on a barrier mean?
It is associated apparatus (the brackets): it sits in the safe area but its output circuit is protected to level ia, suitable for supplying equipment in Zone 0 (EPL Ga) for gas group IIC. The barrier itself must never be mounted in the hazardous area unless it also carries its own protection marking.
What replaces an MTL5541?
Functionally: a 1-channel HART-transparent repeater power supply with matching entity parameters — MTL's own current 5500-series successor, or equivalents in Pepperl+Fuchs' K-system and R. Stahl's ISpac range. We confirm the entity match and supply the certificate with the quote; send the loop details to sales@cballast.com.

References and related guides

Standards referenced: IEC/EN 60079-11 (intrinsic safety); IEC 60079-25 (IS systems); IEC 60079-14 (installation); EN 60947-5-6 (NAMUR); IEC 60079-0 (general requirements and marking); maker documentation for MTL 4500/5500/7000 and Pepperl+Fuchs K-system.

Questions on a loop, a module or an entity check: write to sales@cballast.com. We answer whether or not you buy from us.

Open / Download PDF

Compiled by cBallast for identification and cross-reference. Part numbers, designations and trademarks belong to their respective manufacturers. Confirm ratings and dimensions against the manufacturer's current documentation and the nameplate of the installed equipment before ordering or installation.