Flange Face Types — RF, FF, RTJ and Surface Finish

Reference compiled by cBallast. 8-page PDF; the full content is on this page.
Compiled by
cBallast
Subject
Pipe flanges — facing and finish
Document type
Reference
Reference
2026 edition
Issued
2026-11-09
Pages
8
Format
Web page and PDF

Every flange facing decoded: raised face and its real heights per standard, flat face and why cast bodies demand it, ring-type joint grooves, tongue-and-groove and male-female pairs, the EN 1092-1 type letters (A, B1, B2, C to F) against ASME practice, and the surface-finish numbers — Ra bands, AARH microinch values, the serrated "gramophone" finish — that decide whether a gasket seals or leaks regardless of torque.

The short version

1. The facing catalogue

FacingEN 1092-1 typeASME practiceGasket that belongs to itWhere you meet it
Flat face (FF)Type AFF — cast iron class 125/250 practiceFull-face soft gasket, bolt holes punchedCast iron valves and pumps, bronze marine bodies, FRP, low-pressure water
Raised face (RF)Type B1 (standard finish), B2 (smooth)RF 1.6 mm to Class 300; 6.4 mm from Class 400Ring-pattern soft gasket, spiral-wound, kammprofileThe default everywhere in steel piping
Ring-type joint (RTJ)—RTJ groove per B16.5/B16.20R/RX/BX metal ringsHigh pressure, high temperature, wellhead and refinery classes
Tongue and groove (T&G)Types C (tongue) / D (groove)Rare, special equipmentConfined soft or PTFE gasketReactors, exchangers, gasket confinement for soft/fragile materials
Male and female (M&F) / spigot-recessTypes E (spigot) / F (recess)Rare outside equipment flangesConfined gasket, exact ODHeat exchanger girth flanges, hydraulic equipment, some marine systems
Lap joint / loose flange over stub endType 02/04 combinationsLap-joint classPer the stub-end faceStainless and lined systems — the flange rotates, easing bolt alignment

Mating logic: RF mates RF, FF mates FF, T&G and M&F mate only their counterpart — a tongue without its groove has nowhere to seal, and the pairs also fix gasket OD exactly, which is why confined-face gaskets are ordered by the equipment drawing rather than by DN alone. For the drilling that goes around these faces, the dimension charts are the companions to this page: PN16, PN10, PN25, PN40, Class 150, Class 300, Class 600, JIS 10K and JIS 5K/16K.

2. Raised-face heights and why they bite

Standard / classRaised-face heightConsequence in practice
EN 1092-1, PN-designated steel flanges (type B)2 mm (3 mm at large DN per the standard's tables)EN gasket ring dimensions (EN 1514) sized to the face; face OD shrinks as PN rises at the same DN
ASME B16.5 Class 150 / 3001.6 mm (1/16")Included in the standard's face-to-face and thickness tables — do not add it twice when calculating stud length
ASME B16.5 Class 400 / 600 / 900 / 1500 / 25006.4 mm (1/4")NOT included in some tabulated thickness conventions — the classic stud-length miscalculation; also changes wrench clearance
JIS B2220 10K/16KSmall raised face ("packing seat") per the standardFace diameter differs from EN at the same DN — gasket OD follows JIS, not EN 1514

Stud sizing, which trips even experienced buyers on Class 600 work: stud length = 2 × (flange thickness + raised face where the convention excludes it) + gasket compressed thickness + 2 nut heights + point allowance. When changing a joint from Class 300 to Class 600, everything changes — drilling, face height, stud length and the torque table line. Order studs with the flange, not from memory.

3. Surface finish — the numbers on the face

Finish classRa (μm)AARH (μin)How it is madeGaskets it serves
Stock / serrated ("gramophone")3.2–12.5125–500 (commonly 125–250 specified)Continuous spiral or concentric V-grooves from a round-nosed toolCompressed fibre (Klingersil class), rubber, PTFE sheet — the grooves grip the gasket against creep and blowout
Smooth finish1.6–3.263–125Finer machining passSpiral-wound (B16.20 class), kammprofile, metal-jacketed
RTJ groove / very smooth≤1.6≤63Ground or fine-turnedMetal ring joints; some virgin-PTFE and elastomer duties

Reading a spec: "125–250 AARH" on a data sheet is the arithmetic-average roughness window in microinches — the standard raised-face finish for general service with soft or semi-metallic gaskets. Two field rules. A face reworked by hand-grinding to a shine is a downgrade for fibre gaskets — the gasket needs the serrations; and radial scratches (across the grooves) are the killers, because they give media a straight path outward: radial score deeper than the gasket can fill means re-machining, not a thicker gasket. Assessment is by visual comparison and Ra gauge against the window, with the gasket maker's limits (depth/width of permissible imperfections) as the acceptance criteria.

4. Matching face, finish and gasket — the decision table

Joint situationCorrect combinationClassic error
Steel RF pair, water/oil/gas, moderate pTRF + stock finish + fibre sheet ring gasket, thinnest workable (1.5–2 mm)Mirror-smooth refaced flange + fibre sheet → creep relaxation and blowout
Steel RF pair, steam or cycling dutyRF + 125–250 μin + spiral-wound with inner ring or kammprofileFibre sheet "rated" for the temperature on the headline number — see the pT logic in the Klingersil guide
Cast-iron valve in a steel lineFF counter-flange + full-face gasket; torque in stages, star patternRF steel flange bolted straight to the casting — cracked flange ear, often weeks later
High class (600+), hydrocarbonsRTJ with the correct R-number ring, or RF + spiral-wound per piping classReusing a crushed RTJ ring; mixing octagonal ring into a worn oval groove against the class spec
Glass-lined / FRP / plasticFF + full-face soft gasket, controlled low torque, washers per makerStandard steel-joint torque applied to a lined flange — crushed lining

5. Specifying and buying

A complete flange line on an RFQ reads: standard and rating, size, type (weld-neck, slip-on, blind, lap-joint), facing (RF/FF/RTJ, EN type letter where applicable), finish if non-default, material, and certificate level (EN 10204 3.1 for pressure service). Examples from our catalogue range: ASME B16.5 weld-neck 2" Class 150 A105 (RF), PN16 slip-on DN40 EN 1092-1, and blind positions such as the DN200-pattern blind flange. Gaskets ride the same RFQ: ring or full-face soft gaskets cut to the facing, spiral-wound positions, or RTJ rings by R-number.

How buying works at cballast. We quote flanges with facing and finish stated per line, matching gaskets and stud sets on the same quotation, and we flag mismatches (RF against a cast FF body, fibre sheet on a steam line) rather than shipping them. Accounts are vetted at onboarding; first order prepaid; established accounts on credit terms with repeat discounts; public bodies and utilities invoiced against purchase order from the first order. RFQs to sales@cballast.com.

Frequently asked questions

What is the difference between raised face and flat face flanges?
A raised face concentrates bolt load on a small annular gasket area inside the bolt circle — the standard for steel piping. A flat face spreads the load across the whole flange with a full-face gasket, protecting brittle bodies (cast iron, FRP, bronze) from bending. They are not interchangeable: an RF steel flange bolted to an FF casting cracks the casting.
How high is a raised face?
2 mm on EN 1092-1 type B flanges (3 mm at large sizes per the standard), 1.6 mm (1/16") on ASME B16.5 Class 150/300, and 6.4 mm (1/4") on ASME Class 400 and above. The 1/4" face on high classes changes stud length and must be checked against which thickness convention your table uses.
What does 125–250 AARH mean on a flange spec?
Arithmetic-average roughness height of 125–250 microinches (about Ra 3.2–6.3 μm) — the standard serrated raised-face finish. It is the window where fibre and spiral-wound gaskets perform; smoother invites creep of soft gaskets, rougher exceeds what the gasket can fill.
What is a gramophone (phonographic) finish?
The continuous spiral groove cut into a flange face by a round-nosed tool — named for its resemblance to a record. It is the deliberate "stock finish" that grips soft gaskets. It is not damage and should not be polished off; refacing should reproduce it.
Can I reuse an RTJ ring gasket?
No. The ring seals by plastic deformation into the grooves; once crushed it neither springs back nor re-deforms predictably. Rings are single-use, and grooves should be inspected for the finish (63 μin class) and for radial damage before the new ring goes in — dimensions per the B16.20 ring-joint chart.
Which gasket for a smooth (63–125 μin) face?
Semi-metallic — spiral-wound or kammprofile — or metal-jacketed types; that band exists for them. Fibre sheet on a face that smooth loses the mechanical grip it needs; if the joint must take sheet, the face wants re-serrating to stock finish.
Who supplies flanges with specified facing and finish?
cballast.com quotes EN, ASME, JIS and table-pattern flanges with facing and finish stated per line, plus the matching gaskets and stud sets. Send the line list to sales@cballast.com.

References and related guides

Standards and sources referenced: EN 1092-1 (facing types A–F, finish classes); ASME B16.5 (facings, finish practice); ASME B16.20 (RTJ rings, spiral-wound); ASME B16.21 / EN 1514-1 (soft gasket dimensions); gasket manufacturers' flange-surface acceptance criteria.

Questions on a facing call-out or a refacing acceptance: write to sales@cballast.com. We answer whether or not you buy from us.

Open / Download PDF

Compiled by cBallast for identification and cross-reference. Part numbers, designations and trademarks belong to their respective manufacturers. Confirm ratings and dimensions against the manufacturer's current documentation and the nameplate of the installed equipment before ordering or installation.