Klingersil Gasket Sheet Grades — Cross-Reference Chart

Reference compiled by cBallast. 8-page PDF; the full content is on this page.
Compiled by
cBallast
Subject
Compressed fibre gasket sheet
Document type
Reference
Reference
2026 edition
Issued
2026-11-09
Pages
8
Format
Web page and PDF

The Klingersil compressed-fibre gasket sheet grades decoded — C-4400, C-4430, C-4500, C-4509, C-4324 and the specialty grades — with fibre and binder chemistry, media suitability, the pT-diagram logic that actually governs temperature and pressure limits, sheet thickness selection, equivalents thinking across Garlock, Donit and Temacs class materials, PTFE (Gylon class) and graphite alternatives, and cut-gasket against sheet buying.

The short version

1. The grade table

GradeFibre / binderCharacterTypical mediaCatalogue anchors
C-4400Aramid / NBRThe universal grade; broad chemical window, good mechanical strengthWater, seawater, oils, fuels, gases, moderate steam duty per pTC-4400 sheet 1/16" x 59" x 59"; cut gaskets e.g. DN15 PN16, DN20 PN16
C-4430Aramid + glass / NBRHigher load-bearing and steam capability than C-4400Steam per pT, hot water, oils, gases — the plant upgrade gradeC-4430 sheet 1/16" x 59" x 59"
C-4500Carbon / NBRTemperature capability above the aramid gradesHot oils, heat-transfer duties, steam per pTQuoted by sheet or cut gasket
C-4509Carbon / NBR (oil-service recipe)Heat plus hydrocarbon resistanceThermal oil, hot hydrocarbon linesQuoted by sheet or cut gasket
C-4324Aramid / NBR (economy)General service where duty is mild and price mattersWater, air, oils at modest pTC-4324 sheet 1500 x 1000 x 2.0 mm

Adjacent Klinger families complete the picture: Klinger ML1 universal sheet for undemanding service (ML1 1500 x 1000 x 2 mm), top-sil and top-chem engineered sheets — the top-chem 2000 cut gasket DN32 PN16 is the PTFE-class answer for aggressive media — and expanded-PTFE tape (Sealex 14 x 5 mm) for field-formed sealing on damaged faces.

2. Reading a pT diagram like the datasheet means it

The axes are internal pressure and temperature; the curve divides three regions. Region one (low p, low T): the sheet serves with ordinary assembly practice. Region two: serviceable only with engineering review — controlled bolt load (torque charts), flange condition verified, thinner sheet, sometimes inner eyelets. Region three: choose another material. Two consequences professionals act on: first, steam moves every fibre sheet deep into region two long before the headline temperature — which is why steam mains migrate to graphite or spiral-wound even at modest pressures; second, the diagram assumes correct surface pressure, so an under-torqued joint fails in region one too. For critical joints Klinger's published gasket factors (and EN 13555 data where the design method is EN 1591) complete the calculation; for routine flange work the pT check plus the standard torque table is the working method.

3. Thickness, surface condition and assembly

Flange conditionSheet thicknessNote
Good machined faces, standard raised face1.5 mmDefault — best blowout and creep behaviour
Minor scoring, light corrosion, large diameters2.0 mmThe practical plant standard for DN>300 and older flanges
Warped or heavily worn faces3.0 mmA repair measure; plan to machine the face instead

Assembly is half the gasket's performance: faces cleaned to bare metal, gasket dry (no grease on fibre sheet — it destroys the friction the seal depends on), bolts lubricated and pulled in a star pattern to the torque table in stages, and a retorque where the procedure calls for it. Dimensions for cut gaskets follow the flange standard — EN 1092-1 ring dimensions in our PN16 chart and siblings, full-face for flat-face flanges — and the flange finder resolves the pattern when the drawing is missing.

4. Equivalents thinking across makers

Recipe classKlinger gradePeer-class examplesEquivalence caveat
Aramid/NBR universalC-4400Garlock Blue-Gard 3000 class, Donit and Temac aramid/NBR sheetsMatch pT behaviour and approvals line by line
Aramid+glass/NBR, steam-capableC-4430Peer high-load aramid gradesSteam capability differs by maker — pT diagrams decide
Carbon/NBR high temperatureC-4500 / C-4509Peer carbon/NBR gradesThermal-oil approvals vary
Restructured PTFEtop-chem familyGarlock Gylon 3510 classFiller chemistry (silica, barium sulphate, glass) sets media fit
Graphite laminateKlinger graphite programmePeer graphite sheets, tanged or foil-reinforcedOxidation limit in air; reinforcement type matters for handling

"Equivalent" on a requisition means: same recipe class, pT envelope covering the duty, and the named approvals present (WRAS/KTW drinking water, DVGW gas, BAM oxygen, API/fire test where piping class demands). A cheaper sheet missing the approval is not an equivalent, it is a different product — the same honesty rule as everywhere in our gasket material guide.

5. Buying: sheet, cut gaskets, or kits

Sheet (standard formats 1000 x 1500 and 1500 x 2000 mm, thicknesses 0.5–3 mm) suits workshops that cut their own; cut gaskets to EN 1092-1 or ASME patterns suit everyone else — dimensional consistency, no nesting waste, and traceability printed per gasket. Flange isolation sets (isolation kit guide) and ring-joint or spiral-wound positions ride the same requisition. A quotable line: grade (or recipe class plus approvals if open), dimension (DN/PN or ASME NPS/class, or sheet format), thickness, quantity, and the medium/temperature/pressure so the pT check can be confirmed on our side — we flag lines where the requested grade sits in region two of its diagram rather than quoting blind.

How buying works at cballast. We quote Klinger, Garlock and peer sheet and cut gaskets with the pT sanity check included, approvals stated per line, and standing lists for plants that order by the drawing. Accounts are vetted at onboarding; first order prepaid; established accounts on credit terms with repeat discounts; public bodies and utilities invoiced against purchase order from the first order. RFQs to sales@cballast.com.

Frequently asked questions

What is the difference between Klingersil C-4400 and C-4430?
Both are NBR-bound fibre sheets: C-4400 uses aramid fibre and is the universal industrial grade; C-4430 adds glass fibre for higher load-bearing and better steam capability. On water, oils and gases they overlap; where steam or higher surface pressure appears, C-4430 is the step up — confirmed on its pT diagram, not the headline temperature.
What temperature can Klingersil C-4400 handle?
Its pT diagram is the answer: the headline maximum (400 °C class, short-term) applies only near zero pressure. At realistic flange pressures the freely usable region ends far lower — think in terms of the 150–250 °C band for continuous duty depending on pressure, and route anything hotter or steam-heavy through the diagram or to graphite/spiral-wound territory.
Is there a Klingersil C-4400 equivalent?
By recipe class, yes: aramid/NBR compressed fibre sheets from Garlock (Blue-Gard class), Donit, Temac and peers. A true equivalent matches the pT envelope and carries the same approvals the duty needs (drinking water, gas, oxygen). We cross grades with the approvals checked line by line — send the duty, not just the grade name.
Which gasket sheet thickness should I use?
The thinnest the flanges allow: 1.5 mm default on good faces, 2 mm for rough or large flanges, 3 mm only as a stopgap for faces that really need machining. Thinner sheet creeps less, resists blowout better and needs less bolt load to reach sealing stress.
Can I grease a fibre gasket to help it seal?
No — grease on compressed-fibre sheet destroys the surface friction the joint depends on and promotes extrusion. Fit dry on clean faces; lubricate the bolts, not the gasket, and pull to the torque table in stages.
Who supplies Klingersil sheets and cut gaskets?
cballast.com quotes Klinger sheet formats and cut gaskets to EN 1092-1 and ASME patterns, Garlock and PTFE alternatives beside them, with the pT check and approvals stated per line. Send grades, dimensions and duties to sales@cballast.com.

References and related guides

Standards and sources referenced: Klinger pT diagrams and grade datasheets (C-4400, C-4430, C-4500, C-4509, C-4324, top-chem); EN 1514-1 (flange gasket dimensions); EN 13555 / EN 1591 (gasket factors and flange calculation); ASME B16.21 (non-metallic flat gaskets); approval schemes WRAS, KTW, DVGW, BAM.

Questions on a grade, a pT check or a cut pattern: write to sales@cballast.com. We answer whether or not you buy from us.

Open / Download PDF

Compiled by cBallast for identification and cross-reference. Part numbers, designations and trademarks belong to their respective manufacturers. Confirm ratings and dimensions against the manufacturer's current documentation and the nameplate of the installed equipment before ordering or installation.