The procurement side of marine turbochargers: reading the rating plate so the RFQ identifies the machine exactly, the family landscape from ABB (VTR, TPS, TPL, A100/A200) through MAN (NR, TCR, TCA), Napier, KBB and Mitsubishi MET, what wears and what gets renewed at overhaul — bearings, nozzle rings, sealing and the cartridge question, high-speed small-bore practice with CHRA cartridges, surge and fouling symptoms that announce which parts are due, and how overhaul exchange against spares supply actually gets bought.
| Maker / family | Construction notes | Habitat | Spares pattern |
|---|---|---|---|
| ABB (now Accelleron) VTR | The classic large radial-turbine machine; plain bearings, generations of retrofits | Older two-strokes and large four-strokes, still everywhere | Bearings, nozzle rings, sealing, blading — component-level overhaul culture |
| ABB TPS (…D/E) | Compact radial machines for gensets and small propulsion | Auxiliary engines, smaller mains | Bearing kits, cartridges on the smaller frames, nozzle rings |
| ABB TPL (…B/C) | Axial-turbine, large engine mainline | Modern two-stroke mains and large four-strokes | Component overhaul against maker service steps; blading and bearing work at scope |
| ABB A100/A200 class | Current high-efficiency generations | Modern builds | Maker/licensed network dominant early in life |
| MAN (NR legacy, TCR radial, TCA axial) | Parallel family logic to ABB | MAN engines and licensees | As above — plate data decides everything |
| Napier (NA/7-series class) | Radial machines with strong genset presence | Auxiliaries, medium-speed engines | Nozzle rings, bearings, cartridges on small frames |
| KBB, Mitsubishi MET | KBB on smaller engines; MET axial machines on large two-strokes | Per engine licence | Family-specific; same identification discipline |
| High-speed small-bore (Holset, Garrett class) | Automotive-derived, ball/plain cartridge construction | Harbour craft, emergency gensets, auxiliary machinery — e.g. Holset HX35 CHRA | CHRA exchange is the normal repair — hours are cheap, cartridges are stocked |
| Part | Failure/wear mode | Renewal logic |
|---|---|---|
| Journal and thrust bearings | Hours, oil quality events, stop/start duty | On maker hours without debate — the cheapest insurance on the machine; oil cleanliness per our ISO 4406 guide decides how kind those hours are |
| Nozzle ring (turbine inlet vanes) | Hot-gas erosion, HFO ash fouling, foreign-object nicks | Inspect at every opening; renew on erosion/crack criteria — the classic performance-loss part |
| Labyrinth seals / sealing bushes | Rub, wear, oil carry-over symptoms | Renew at overhaul; oil in the compressor or blue smoke names them early |
| Compressor wheel | Tip rub, FOD, fatigue in salt-laden air | Inspect/balance at scope; renew on criteria |
| Turbine blading / rotor (axial machines) | Erosion, deposits, creep at the hot end | Maker-scope work with balancing — serial-bound parts |
| Filter silencer elements, gaskets, O-ring sets | Service consumables | Every opening; keep on board |
| Cartridge / CHRA (small frames) | All of the above, bought as one unit | Exchange beats component repair below a frame size — hours back in a day |
The decision between component overhaul and cartridge/unit exchange is frame-size economics: large machines are overhauled in place or in shop per the maker's service steps; small high-speed units exchange as CHRA cartridges because the labour of component repair exceeds the cartridge. Mid-frames (genset TPS/Napier classes) go either way — quote both and let the yard window decide.
| Symptom | Usual story | Parts conversation |
|---|---|---|
| Surging (audible barking/howling under load changes) | Fouled compressor/turbine, eroded nozzle ring, flow mismatch after engine work, charge-air path restriction | Washing first; nozzle ring inspection; filter elements; charge-air cooler cleaning on the engine side |
| Exhaust temperatures up, scavenge/boost down | Efficiency loss — fouling or worn hot-side geometry | Nozzle ring, turbine-side cleaning, sealing wear check |
| Oil in compressor / blue smoke / oil loss | Sealing bushes/labyrinths, bearing drain issues | Seal set + bearing inspection; check drain and venting before blaming the turbo twice |
| Vibration, noise at speed | Bearing wear, imbalance from deposits or blade damage | Bearings on hours; wheel/blading inspection with balancing |
| Slow spool after maintenance elsewhere | Leaking charge-air or exhaust joints, wrong gaskets | Joint kits — cheap, and often the whole story |
From the rating plate: maker, type designation exactly as stamped, serial number, specification/part-list number where shown. From the PMS: running hours since last overhaul and the planned scope. From the engine side: engine maker/type and position (main/aux) — useful context, never a substitute for the plate. Then the commercial frame: component list or exchange unit, yard window dates, delivery port, and the documentation demanded (class survey items want traceable paperwork — works certificates per EN 10204 class, and where the machine is survey-bound, the channel question answered explicitly: OEM, licensed repairer, or independent with stated provenance). Planning synergy: turbo scopes belong inside the drydock and survey planning cycle — see the survey spares planning guide — because the machine's opening windows are the yard's windows, and freighting a nozzle ring to a quay is cheaper than freighting it to an anchorage. Engine-level context for the big Wärtsilä families lives in our W32, W46 and W38/50DF spares references.
How buying works at cballast. We quote turbocharger spares and exchange units with the channel and documentation stated per line — OEM-pattern, licensed or independent with provenance — matched to plate data you send, and consolidated with the rest of the yard list. Accounts are vetted at onboarding; first order prepaid; established accounts on credit terms with repeat discounts; public bodies and utilities invoiced against purchase order from the first order. RFQs to sales@cballast.com.
Standards and sources referenced: manufacturer service documentation and service-letter practice (ABB/Accelleron VTR/TPS/TPL/A-series, MAN NR/TCR/TCA, Napier, KBB, Mitsubishi MET families); classification society survey requirements for machinery; EN 10204 for documentation levels.
Questions on a plate you cannot fully read or a scope decision: write to sales@cballast.com. We answer whether or not you buy from us.