Graco Reactor Proportioners — E-30, H-50, XP Selection

Guide compiled by cBallast. 8-page PDF; the full content is on this page.
Brand
Graco
Subject
Plural-component proportioners
Document type
Guide
Reference
2026 edition
Issued
2026-11-09
Pages
8
Format
Web page and PDF

Choosing and running Graco Reactor plural-component proportioners for spray foam and polyurea: what the model grammar means (E, H and A drives; 30/50 output classes; XP pressure classes; Reactor 2 against Reactor 3; Elite packages), how foam and coatings duties push the choice differently, heater and hose sizing against real site conditions, the spare parts and consumables that keep a rig earning, and what a complete RFQ for a machine or a rebuild looks like.

The short version

1. The model grammar

ElementMeaningWorking consequence
E / H / A prefixElectric, hydraulic or air driveE = site-friendly, generator-driven work (e.g. Reactor 2 E-30 package); H = highest duty cycles and outputs (e.g. Reactor 3 H-50 Elite); A = entry/touch-up class
Output number (30 / 40 / 50…)Output class — the E-30 family sits near ~13.5 kg/min maxMatch to gun chamber size and crew pace; chronic max-output running means the machine is undersized
XP suffixHigh-pressure class (~3500 psi) for polyurea/coatingsDifferent pumps and ratings — an H-XP2/H-XP3 is a coatings machine first
Reactor 2 vs Reactor 3Generation: controls, data, platformReactor 3 brings the connected ecosystem and refined diagnostics; Reactor 2 packages (e.g. E-30 ES2011) remain fully supported workhorses
Elite tierPremium package content (Xtreme-Wrap hose class, options)Buys hose durability and convenience — worth it for daily-spray contractors
Package voltage (230/400 V) and heater kWElectrical configurationMust match the generator or shore supply — the 15 kW heater package needs the amps to feed it

2. Foam duty or coatings duty — the decision table

DutyPressure classMachine familyWhy
SPF insulation (open/closed cell), roofs, walls, tanks~2000 psi classE-30 class electric; H-40/H-50 for high-volume crewsFlow and heater capacity govern yield and ambient-window; closed-cell winter work is the heater stress test
Polyurea waterproofing, truck beds, secondary containment~3500 psi class (XP)E-XP2 class; H-XP2/XP3 for production ratesFast-gel chemistry needs pressure for clean atomisation at temperature
Mixed contractor (foam + occasional polyurea)Size for the coatings daysXP-class machine run gentler on foam daysDowngrading pressure is easy; the reverse is a new machine
Marine/industrial maintenance (pipe coating, tank lining)Per system datasheetOften XP class + specific gun chambersCoating systems specify pressure/temperature windows — the machine serves the chemistry, not vice versa

Generator sizing belongs in this table's margins: the proportioner, both primary heaters, hose heat and the air compressor all draw together at spray start. The package's own electrical data decides — reading it before the site day is cheaper than discovering voltage sag as cold joints and off-ratio events.

3. Heat and hose — where output actually gets made

Spray chemistry works in a narrow temperature window at the gun. Three heat stages get it there: primary heaters (A and B), the heated hose holding temperature over distance, and the whip hose at the gun. Practical sizing rules: pick the heater kW for the climate and material (winter closed-cell at high flow is the governing case — the 15 kW class package earns its price the first cold morning); pick hose length for the real site geometry, remembering every section adds thermal load and pressure drop; and treat the fluid-temperature sensor and transducers as consumables of the control loop — a Reactor holding ratio but drifting temperature makes bad foam with a green status light. Daily discipline that protects yield: recirculate to temperature before the first pull, TSL in the ISO lube cup (crystallised ISO is the single most common pump killer), drum temperatures managed (agitator/band heaters in the cold), and desiccant on the ISO drum vent because A-side plus moisture equals crystals in the pump and filters.

4. The spares economy — what a working rig carries

CategoryItemsWhy on the van, not on order
Gun serviceMix chambers (sized to output), side-seal kits, gaskets, drill bits for ports, gun rebuild kitThe gun is the wear point — a chamber and seals change-out is minutes if the kit is aboard, a lost day if not
Pump and lubeTSL fluid, ISO-side lube cup parts, pump repair kits per sideISO crystallisation does not wait for freight
Sensing and controlPressure transducers, fluid temperature sensor, hose thermocouple/FTS partsRatio and temperature assurance — the difference between product and liability
HoseOne spare heated section + whip, connection O-rings, insulation wrapHose damage on site is routine; the spare section keeps the day alive
Filtration and feedY-strainer screens (A/B), feed pump service parts, drum fittingsDirty feed shows up as pressure imbalance alarms an hour into the job

Troubleshooting shorthand that the spares list answers: pressure imbalance alarm → look at feed (strainers, drum pumps, empty drum) before blaming the machine; off-ratio or crossover → gun chamber/side seals worn or a check stuck — rebuild kit territory; temperature sag at the gun → heater element or hose zone, measured not guessed; ISO pump stiff after a weekend → TSL discipline failed, crystals in the wet cup. Every one of these is van-stock repairable.

5. Buying a Reactor — the RFQ that gets the right machine

A complete inquiry states: duty (foam class or polyurea/coating system, with the system datasheet if special), daily output target and crew pattern, site electrical reality (shore supply or generator, voltage/frequency — our packages run 230/400 V classes), hose length needed, climate (heater sizing), and whether the purchase is machine-only or turnkey (feed pumps, agitator, gun, spares kit). From our range: Reactor 2 E-30 package, 15 kW, heated hose, Xtreme-Wrap (EH2011) and its ES2011 sibling, the E-30 Elite 10 kW package, and Reactor 3 hydraulics — H-50 Elite, H-XP2 Elite polyurea, H-XP3 Elite. Pumps for transfer and supply live in the same programme — see the Graco Husky AODD selection guide.

How buying works at cballast. We quote machines, packages and the van-stock spares list in one quotation, sanity-check electrical and hose configuration against your site description, and support rebuilds with parts lists per serial. Accounts are vetted at onboarding; first order prepaid; established accounts on credit terms with repeat discounts; public bodies and utilities invoiced against purchase order from the first order. RFQs to sales@cballast.com.

Frequently asked questions

What is a Graco Reactor E-30 used for?
It is an electric plural-component proportioner in the mid-output class (up to roughly 13.5 kg/min) — the standard machine for spray-foam insulation crews and general plural-component work, supplied as packages with primary heaters (10/15 kW classes), heated hose and gun options on 230/400 V supplies.
What is the difference between Reactor 2 and Reactor 3?
Generation. Reactor 3 is the current platform with connected controls, refined diagnostics and data features; Reactor 2 is the proven predecessor, still fully supported and widely run. Chemistry and basic architecture are shared; crews choose on controls, fleet standardisation and budget.
What does XP mean on a Reactor?
The high-pressure class (~3500 psi family) built for polyurea and fast coating systems, against the ~2000 psi class of standard foam machines. If polyurea is anywhere in your order book, buy the XP class — it sprays foam happily, while the reverse upgrade means a second machine.
E-30 or H-50 — electric or hydraulic?
Electric (E) machines suit generator-driven mobile crews and moderate duty cycles; hydraulic (H) drives carry the highest outputs and the hardest daily duty with smoother pressure at the gun. High-volume roofing and industrial crews go H; most insulation contractors are perfectly served by the E-30 class.
Why does my Reactor show a pressure imbalance alarm?
Nine times out of ten the problem is upstream: a clogged Y-strainer, a tired drum pump, an empty or cold drum on one side. Check feed before the machine. Persistent imbalance after clean feed points to pump packings or transducers — both van-stock items on a well-kept rig.
What spare parts should I keep for a Reactor rig?
Gun mix chambers and seal kits, pump repair kits and TSL, pressure transducers and the fluid temperature sensor, one spare heated hose section with O-rings, and strainer screens. That short list covers the stoppages that otherwise cost site days.
Who supplies Graco Reactor machines and parts in Europe?
cballast.com quotes Reactor 2 and Reactor 3 packages, guns, hose and the working spares list, configured against your voltage, climate and duty. Send the duty description to sales@cballast.com.

References and related guides

Standards and sources referenced: Graco Reactor 2 and Reactor 3 series technical documentation and package data (output, pressure and heater classes as published by the manufacturer); plural-component application practice per system suppliers' datasheets.

Questions on a package configuration or a rebuild list: write to sales@cballast.com. We answer whether or not you buy from us.

Open / Download PDF

Compiled by cBallast for identification and cross-reference. Part numbers, designations and trademarks belong to their respective manufacturers. Confirm ratings and dimensions against the manufacturer's current documentation and the nameplate of the installed equipment before ordering or installation.