Festo DSBC & DSNU Cylinder Model Codes Decoded

Reference compiled by cBallast. 8-page PDF; the full content is on this page.
Brand
Festo
Subject
Pneumatic cylinders
Document type
Reference
Reference
2026 edition
Issued
2026-11-09
Pages
8
Format
Web page and PDF

Reading a Festo cylinder type code like DSBC-63-100-PPVA-N3 element by element: series, bore, stroke, cushioning letters (P, PPV, PPS), the A that means a sensing magnet, and the design suffixes — plus the ISO geometry underneath (15552 for profile/tie-rod cylinders, 6432 for rounds, 21287 for compacts) that makes Festo, SMC and Norgren mechanically interchangeable, how to spec a replacement when the label is gone, and the accessories (mountings, fittings, sensors) that belong on the same order.

The short version

1. The code, element by element

ElementValues you will meetMeaning / consequence
SeriesDSBC (ISO 15552 profile), DSNU (ISO 6432 round), ADN (ISO 21287 compact), DSBG (large 15552 class), legacy DNC/DNUFixes the mechanical standard, mounting interfaces and size range; DNC-era codes map to DSBC replacements
Bore (first number, mm)DSBC: 32–125; DSNU: 8–63 classForce = pressure x area: at 6 bar a 32 bore pushes ~480 N, 63 ~1,870 N, 100 ~4,700 N (theoretical, before friction)
Stroke (second number, mm)Catalogue steps + any length to orderLong strokes bring buckling and side-load questions — guide units or bigger rods beyond the tables
CushioningP / PPV / PPSFixed pads / adjustable screws / self-adjusting — see the selection table below
AMagnet includedEnables slot-mounted proximity sensing; specify by default
Design suffixN3 and siblings; C variants (e.g. DSBC-63-35-C-PPVA)Generation/options coding (rod variants, clamping options) — quote the suffix exactly when reordering like-for-like
Further optionsHeat-resistant seals, slow-speed grease, stainless rod, ATEX variantsAppear as extra code groups — state the environment and we resolve them

2. Cushioning selection — the letters that save machines

CodeMechanismRight whenWrong when
PElastic pads at the end capsShort strokes, light loads, modest speedsAny real mass at speed — pads hammer and the machine tells you about it
PPVAdjustable pneumatic cushioning, screw-set each endDefined loads at speed; classic industrial duty; fine control wantedSet-and-forget environments where nobody ever tunes the screws (they arrive mis-set and stay that way)
PPSSelf-adjusting pneumatic cushioningMost modern duty — adapts to load/speed changes without maintenance attentionExtreme corner cases outside its adaptation window (very high mass/speed combinations) — check the sizing data

Field rule: if end caps are cracking, mounts loosening or the machine bangs at stroke end, the cushioning letter (or its adjustment) is the suspect before the mounting is. And cushioning is not a substitute for external shock absorbers where energy is genuinely high — the sizing tables draw that line.

3. Replacing a cylinder with no readable label

MeasureHowResolves
BoreTube OD + series geometry, or measure the piston at overhaulThe force class — first code number
StrokeRod travel between mechanical endsSecond code number
Rod threadThread gauge (e.g. M10x1.25, M16x1.5 per ISO size)Confirms ISO size and rod accessories
Mounting interfaceFoot/flange hole pattern, clevis pin size, trunnionISO mounting code — brackets carry over when the ISO size matches
Port size/positionG1/8, G1/4, G3/8 per sizeFittings reuse; confirms series family
Cushioning screws / magnet sensing present?Look at the caps; is a sensor mounted in the slot?PPV vs PPS vs P; the A option

Those six lines plus a photo quote a replacement across Festo, SMC (CA2 class ISO cylinders, C85 round-body) and Norgren — the ISO interfaces are the point. For odd legacy machines, the finder plus the measured data beats guessing a dead brand's code table. Seal kits are real for the common series and sizes; on small rounds a new cylinder frequently beats a kit on cost — we say which on the quote.

4. The system around the tube

Valves: a double-acting cylinder wants a 5/2 (monostable or bistable per the failure-mode you need) or 5/3 for mid-position — matched by flow, not just port size; the directional valve finder maps Festo VUVG/VUVS/MFH/CPE against SMC and Norgren classes. Speed: one-way flow controls at the cylinder ports (meter-out as the default discipline). Sensing: slot-matched proximity sensors on the A-option magnet. Air preparation: filter-regulator(-lubricator) sized to the branch, drained like you mean it — water in the line is the quiet killer of seals and valves alike. Mountings and rod ends: per ISO size, ordered with the cylinder. A complete RFQ line reads like the code itself: "DSBC-63-100-PPVA-N3, foot mounting HNC-63 class, rod clevis, 2x GRLA-3/8 flow controls, 2x proximity sensors for T-slot" — one line, one working axis.

How buying works at cballast. We quote Festo-pattern cylinders and ISO equivalents (stated per line), seal kits where they make economic sense, and the mounting/valve/sensor completion so the axis arrives installable. Accounts are vetted at onboarding; first order prepaid; established accounts on credit terms with repeat discounts; public bodies and utilities invoiced against purchase order from the first order. RFQs to sales@cballast.com.

Frequently asked questions

What does DSBC-63-100-PPVA-N3 mean?
Festo DSBC series (ISO 15552 profile cylinder), 63 mm bore, 100 mm stroke, PPV adjustable pneumatic cushioning, A = position-sensing magnet, N3 design variant. It is a double-acting standard cylinder; force at 6 bar is roughly 1.9 kN theoretical on the push stroke.
What is the difference between PPV and PPS cushioning?
PPV is adjustable pneumatic cushioning tuned by screws at each end cap; PPS is self-adjusting and needs no tuning. PPS is the sensible default for most duty; PPV remains right where a commissioning engineer wants explicit control over deceleration of a defined load.
Can I replace a Festo cylinder with SMC or Norgren?
If it is an ISO cylinder (DSBC = ISO 15552, DSNU = ISO 6432, ADN = ISO 21287), yes — same bore/stroke/mounting interchanges mechanically across brands. Match cushioning type and the magnet option, and re-use the ISO brackets. We state "ISO equivalent" explicitly on such lines.
How do I identify a pneumatic cylinder without a label?
Measure bore, stroke, rod thread and the mounting pattern, note port sizes, cushioning screws and whether a sensor sits in the slot. Those data plus a photo resolve the ISO size and a current type code — the method in section 3 above.
Are seal kits available for Festo cylinders?
For the common series and sizes, yes, and they are worth it on larger bores. On small round cylinders the labour frequently exceeds a new unit's price — we quote both ways and say which is rational per size.
What does the A in PPVA mean?
A built-in magnet on the piston for slot-mounted proximity sensors. It adds almost nothing to the price and cannot be retrofitted — specify it by default even if sensing comes later.
Who supplies Festo DSBC and DSNU cylinders?
cballast.com stocks and quotes the DSBC/DSNU pattern across bores and strokes with mountings, valves, fittings and sensors on the same quotation — plus ISO-equivalent alternatives stated per line. Write to sales@cballast.com.

References and related guides

Standards and sources referenced: ISO 15552, ISO 6432, ISO 21287 (cylinder interfaces); Festo catalogue type-code documentation for DSBC/DSNU/ADN families; peer data (SMC, Norgren) for ISO interchange.

Questions on a code you cannot fully read or an ISO cross: write to sales@cballast.com. We answer whether or not you buy from us.

Open / Download PDF

Compiled by cBallast for identification and cross-reference. Part numbers, designations and trademarks belong to their respective manufacturers. Confirm ratings and dimensions against the manufacturer's current documentation and the nameplate of the installed equipment before ordering or installation.