Hose Clamps — Worm-Drive, Heavy-Duty Bolt and T-Bolt Patterns, Sized and Torqued
Selection guide compiled by cBallast. 3-page PDF; the full content is on this page.
Compiled by
cBallast
Subject
Hose clamps
Document type
Selection guide
Reference
2026 edition
Issued
2026-10-18
Pages
3
Format
Web page and PDF
Reading clamp ranges like the stocked 12–22 and 20–32 mm bands, where worm-drive stops being enough and heavy-duty bolt clamps begin, band width and material choices, the two-clamp rule on suction and fuel, and torque discipline including the re-torque nobody does.
Three patterns, honestly ranked
Pattern
Build
Right for
Worm-drive
Perforated or embossed band, screw housing — the stocked ranges read straight: 12–22 mm, 20–32 mm, 25–40 mm
General water, air, drain duty on soft hose at modest pressure
Heavy-duty bolt (GBS pattern)
Solid band, trunnion bolt — no perforations to bite the hose, far higher clamping force
Reinforced hose, charge-air, agricultural and suction duty
T-bolt
Rolled-edge solid band, T-bolt and nut
Silicone hose, turbo/charge-air, anywhere even radial pressure and real torque both matter
Band width scales with hose wall: 9 mm bands for light hose, 12+ mm where the wall is thick — a narrow band at high torque cheese-wires soft hose. Material marks matter in damp plant: W1 (zinc-plated steel) rusts indoors, W2/W3 mixed builds survive splashing, W4 (AISI 304 throughout) is the washdown default and W5 (316) the coastal/chemical one — same logic as the steel-grade guide.
Fitting discipline
Pick the range so the closed clamp sits mid-range on the installed hose — a clamp at its minimum has run out of band bite; at maximum, out of adjustment.
Position behind the fitting's barb/bead, square to the hose, housing accessible — a clamp seated on the smooth shank seals nothing.
Torque to the clamp maker's figure (single-digit Nm for small worm drives — a cordless driver on full is how housings strip), then re-torque after first thermal cycles: rubber cold-flows under the band, and the 24-hour re-torque is the cheapest leak prevention in the plant.
Two clamps, housings opposed, on suction lines, fuel and anything whose failure drains a tank — and never any worm-drive on steam assemblies, which take bolted steam fittings by rule.
Around 290 clamp line items are stocked across ranges, widths and W-grades, heavy-bolt and T-bolt patterns included — quoted within 24 hours by installed hose outside diameter (measure it clamped loose, not the nominal bore), width and material grade.
Frequently asked questions
What size hose clamp do I need for a 25 mm hose?
Measure the hose's outside diameter over the fitting — a 25 mm bore hose with a thick wall can land near 35 mm OD — then choose the range whose midpoint hits it, like the stocked 25–40 mm band.
When is a worm-drive clamp not enough?
On reinforced or silicone hose, charge-air and suction duty, and anywhere the perforated band's bite or limited force shows — that is heavy-duty bolt and T-bolt territory, with solid bands and real clamping force.
Why did a tight clamp start weeping a week later?
Rubber relaxed under the band — cold flow after the first heat cycles. The fix is the scheduled re-torque a day into service, not a bigger clamp; chronic weepers also hint the clamp sits on the shank instead of behind the barb.
Where the consequence of one letting go is a drained tank or a fire risk, doubled clamps with housings 180° apart are cheap redundancy — marine practice made it a rule, industrial practice does well to copy it on suction and fuel.