Siemens 6ES7132-7GD00-0AB0 — SIMATIC S7 automation module. Compact controller or expansion module for the S7-1200 or S7-1500 PLC platform. SIMATIC ET 200iSP 4DQ 23.1 V DC/20 mA SHUT DOWN "L".
Siemens 6ES7132-7GD00-0AB0 — SIMATIC S7 automation module. Compact controller or expansion module for the S7-1200 or S7-1500 PLC platform. SIMATIC ET 200iSP 4DQ 23.1 V DC/20 mA SHUT DOWN "L".
| Manufacturer part number (MPN) | 6ES7132-7GD00-0AB0 |
| EAN / GTIN | 4019169150187 |
| Sales unit | pcs |
| Product type designation | 4DQ 23.1 V DC/20 mA |
| HW functional status | 7 |
| Firmware version | V3.0.0 |
| Rack mounting | No |
| Front mounting | Yes |
| Rail mounting | Yes |
| Wall mounting/direct mounting | No |
| Type of supply voltage | DC |
| Current consumption, typ. | 290 mA |
| From load voltage (power bus), max. | 340 mA; with actuator supply |
| Power loss, typ. | 2.5 W |
| Address space per module — Address space per module, max. | 2 byte |
| Fieldbus connection via separate transceiver | Yes |
| Type of digital output | Transistor |
| Number of digital outputs | 4; additionally 1 intrinsically-safe input for L shutdown |
| No-load voltage Uao (DC) | 23.1 V |
| Internal resistor Ri | 275 Ω |
| Trend key points E — Voltage Ue (DC) | 17.6 V |
| Trend key points E — Current Ie | 20 mA |
| Output voltage — Type of output voltage | DC |
| Output current — for signal "1" rated value | 0.02 A |
| Output delay with resistive load — "0" to "1", max. | 2 ms |
| Output delay with resistive load — "1" to "0", max. | 1.5 ms |
| Parallel switching of two outputs — for uprating | No; for Ex reasons not possible; nor for predecessor |
| Switching frequency — with resistive load, max. | 100 Hz |
| Switching frequency — with inductive load, max. | 2 Hz |
| Cable length — shielded, max. | 500 m |
| Cable length — unshielded, max. | 500 m |
| Number of PROFINET interfaces | 0 |
| Number of RS 485 interfaces | 0 |
| Diagnoses — Wire break | Yes; R > 10 kohms, I < 100 µA |
| Diagnoses — Short-circuit | Yes; R< 80 Ohm (one output), R< 40 Ohm (outputs connected in parallel) |
| Module for Ex(i) protection | Yes; for more Co/Lo combinations, see certificate IECEx KEM 05.0011 |
| Maximum values for connecting terminals for gas group IIC — Uo (no-load voltage), max. | 25.6 V |
| Maximum values for connecting terminals for gas group IIC — Io (short-circuit current), max. | 96 mA |
| Maximum values for connecting terminals for gas group IIC — Po (power output), max. | 0.61 W |
| Maximum values for connecting terminals for gas group IIC — Co (permissible external capacity), max. | 98 nF |
| Maximum values for connecting terminals for gas group IIC — Lo (permissible external inductivity), max. | 3 mH |
| Maximum values for connecting terminals for gas group IIC — Ui (intrinsically safe input voltage), max. | 28 V; switch input circuit |
| Maximum values for connecting terminals for gas group IIC — Pi (intrinsically safe input power), max. | 1.2 W; switch input circuit |
| Maximum values for connecting terminals for gas group IIC — Ci (internal capacity), max. | 3 nF; switch input circuit |
| IP degree of protection | IP30 |
| CE mark | CE 0344 |
| UKCA mark | DEKRA 21UKEX0085 Importer UK: Siemens plc Manchester M20 2UR |
| CULus | LISTED E334384 |
| FM approval | CLASSIFIED 3025852 |
| INMETRO certificate | UL-BR 12.0073 |
| Use in hazardous areas — ATEX marking | II 2 G (1) G Ex ib [ia Ga] IIC T4 Gb II 2 G (1) D Ex ib [ia IIIC Da] IIC T4 Gb I M2 Ex ib [ia] I Mb |
| Use in hazardous areas — ATEX certificate | KEMA 04 ATEX 1249 |
| Use in hazardous areas — IECEx | IECEx KEM 05.0011 |
| Use in hazardous areas — CCC Ex | 2020322316002945 |
| Use in hazardous areas — EAC Ex | PB Ex ib [ia] I Mb 1Ex ib [ia Ga] IIC T4 Gb [Ex ia Da] IIIC |
| Use in hazardous areas — FM marking | Class I, Zone 1 AEx ib [ia] IIC T4 Ex ib IIC T4 NI, Class I, DIV.2, GP. A,B,C,D T4 AIS, Class I, DIV.1, GP. A,B,C,D T4 DIP Class II, III, GP. E,F,G |
| Use in hazardous areas — Explosion protection category for gas | ATEX gas explosion protection, Zone 1 |
| Use in hazardous areas — Explosion protection category for dust | ATEX dust explosion protection, Zone 21 always install in corresponding enclosure |
| Design of electrical connection | Screw/spring-type terminal |
| Dimensions — Width | 30 mm |
| Dimensions — Height | 129 mm |
| Dimensions — Depth | 136.5 mm |
| Weight, approx. | 255 g |
| Voltage type (supply voltage) | DC |
| Type of voltage (input voltage) | DC |
| Output current | 0.02 A |
| Type of output voltage | DC |
| Degree of protection (IP) | IP30 |
| Type of electric connection | Screw-/spring clamp connection |
| SIL according to IEC 61508 | None |
| Performance level according to EN ISO 13849-1 | None |
| Explosion safety category for gas | ATEX gas-ex-protection, Cat. 2G |
| Width | 30 mm |
| Height | 129 mm |
| Depth | 136.5 mm |
| Country of origin | Germany |
| MOQ | 1 |